Difference between revisions of "Memory Map"
m (→General Memory Map: Oops, fixed the table) |
|||
| (One intermediate revision by one other user not shown) | |||
| Line 1: | Line 1: | ||
| + | {{Pandocs|memory-map}} | ||
| + | |||
The gameboy has a 16bit address bus, that is used to address [[ROM]], [[RAM]], and [[I/O registers]]. | The gameboy has a 16bit address bus, that is used to address [[ROM]], [[RAM]], and [[I/O registers]]. | ||
| Line 11: | Line 13: | ||
|3FFF | |3FFF | ||
|16KB ROM bank 00 | |16KB ROM bank 00 | ||
| − | |From cartridge, fixed bank | + | |From cartridge, usually a fixed bank |
|- | |- | ||
|4000 | |4000 | ||
Latest revision as of 21:11, 4 April 2020
The copy of Pan Docs hosted on this wiki is considered deprecated.
Pan Docs is now officially hosted on gbdev.io as a living document. Please go to https://gbdev.io/pandocs/ to read Pan Docs or to https://github.com/gbdev/pandocs to contribute.
Click here to go to this section of Pan Docs in the new location: https://gbdev.io/pandocs/#memory-map
The gameboy has a 16bit address bus, that is used to address ROM, RAM, and I/O registers.
Contents
General Memory Map
| Start | End | Description | Notes |
| 0000 | 3FFF | 16KB ROM bank 00 | From cartridge, usually a fixed bank |
| 4000 | 7FFF | 16KB ROM Bank 01~NN | From cartridge, switchable bank via MBC (if any) |
| 8000 | 9FFF | 8KB Video RAM (VRAM) | Only bank 0 in Non-CGB mode
Switchable bank 0/1 in CGB mode |
| A000 | BFFF | 8KB External RAM | In cartridge, switchable bank if any |
| C000 | CFFF | 4KB Work RAM (WRAM) bank 0 | |
| D000 | DFFF | 4KB Work RAM (WRAM) bank 1~N | Only bank 1 in Non-CGB mode
Switchable bank 1~7 in CGB mode |
| E000 | FDFF | Mirror of C000~DDFF (ECHO RAM) | Typically not used |
| FE00 | FE9F | Sprite attribute table (OAM) | |
| FEA0 | FEFF | Not Usable | |
| FF00 | FF7F | I/O Registers | |
| FF80 | FFFE | High RAM (HRAM) | |
| FFFF | FFFF | Interrupts Enable Register (IE) |
Jump Vectors in first ROM bank
The following addresses are supposed to be used as jump vectors:
- RST commands: 0000,0008,0010,0018,0020,0028,0030,0038
- Interrupts: 0040,0048,0050,0058,0060
However, the memory may be used for any other purpose in case that your program doesn't use any (or only some) RST commands or interrupts. RST commands are 1-byte opcodes that work similar to CALL opcodes, except that the destination address is fixed. Since they are only 1 byte large, they are also slightly faster.
Cartridge Header in first ROM bank
The memory at 0100-014F contains the cartridge header. This area contains information about the program, its entry point, checksums, information about the used MBC chip, the ROM and RAM sizes, etc. Most of the bytes in this area are required to be specified correctly. For more information read the chapter about The Cartridge Header.
External Memory and Hardware
The areas from 0000-7FFF and A000-BFFF may be used to connect external hardware. The first area is typically used to address ROM (read only, of course), cartridges with Memory Bank Controllers (MBCs) are additionally using this area to output data (write only) to the MBC chip. The second area is often used to address external RAM, or to address other external hardware (Real Time Clock, etc). External memory is often battery buffered, and may hold saved game positions and high score tables (etc.) even when the Game Boy is turned off, or when the cartridge is removed. For specific information read the chapter about Memory Bank Controllers.
Echo RAM
The memory range E000-FDFF is a mirror (or "echo") of WRAM, both for reading and writing. For example, writing to $E123 will modify both $C123 and $E123. It is recommended to avoid using this memory range anyways. This memory range's behavior has been confirmed on all grey GBs as well as on CGB and GBA. Some emulators (such as VisualBoyAdvance <1.8) don't emulate Echo RAM. It is possible to check if Echo RAM is properly emulated by writing to WRAM (avoid values 00 and FF) and checking if said value is mirrored in Echo RAM.
FEA0-FEFF range
This range is very poorly documented. It doesn't even have a name ! From my experience, this stays 00 on DMG, and alternates between 00 and seemingly random values on CGB.
